Acrylic EIFS Paint

Acrylic EIFS paint

Our acrylic EIFS paint 100%  acrylic copolymer  based. Its a very durable exterior or interior coating. Once dry acrylic EIFS paint is fade resistant. It is not affected by alkali in masonry surfaces. acrylic EIFS paint is compatible with Stucco Finish if a color change is desired.

Below is the technical info for acrylic EIFS paint. New to stucco? you can find some basic (how to) videos here

Packaging

5 gallon pail.

Coverage

about 800 to 1000 s/f over stucco finish.

Note. Coverage may varies on job condition.

Storage

Store acrylic EIFS paint in its original pail. Keep at temps from 40º F to 110º F. Store out of direct sunlight. Do not stack over 3 pails high.

Shelf Life

About 2 years.

Surface Preparation

Remove surface contaminants. 1 For previously painted surfaces. Paint must be removed. Glossy surfaces must be dulled. New concrete must be clean and cured. acrylic EIFS paint can be applied to gypsum sheathing. acrylic EIFS paint can be treated with drywall finishing procedures. 2 For metal surfaces. Remove oxides from surface. Prime with 2 coats of non-oil based metal primer.

Approved Substrates

Concrete block. Gypsum sheathing. Densglas® Gold. Poured concrete. Cement board. Acrylic based finishes and stucco. Do not use over wood products or painted surfaces without proper preparation.

Mixing

Mix acrylic EIFS paintto a workable consistency. No thinning is required for brush or roller application. A small amount of clean water may be added for workability. Close container when not in use.

Note: No other additives of any kind  shall be added.

Application Directions

acrylic EIFS paint exhibits good coverage. It may be applied by brush, roller, or spray. Two coats may be required.

For one coat application. Surface must be clean, dry and free of contaminants. Clean surfaces with a mild detergent. Rinse wall with water. Allow to dry. Apply acrylic EIFS paint with a brush or roller. Use a med to long nap to cover rough surfaces. For spray application. Use the following as a guide: Tip.016 to .021. Fan. 40º to 60º (8″ to 10″ fan). Pressure. 800 to 1600 psi. Brush, roll or spray out in all  directions. Maintain a wet edge at all times.

For two coat application. Allow the first coat to dry. Apply the second coat.

Precautions. Limitations

Temps must be at least 40º F during application and drying period. Do not use on wet surfaces. Do not use in very cold temps. Keep product safe from the elements. Avoid application over irregular surfaces.

Cleanup

Clean brushes, rollers and spray equipment with warm water.  Follow up with mineral spirits in spray equipment.

Warning

KEEP PAIL CLOSED WHEN NOT IN USE. KEEP OUT OF REACH OF CHILDREN. NOT FOR INTERNAL CONSUMPTION. THIS PRODUCT IS FOR PROFESSIONAL USE ONLY BY A QUALIFIED TECHNICIAN.

Info contained here is to the standard specs and details of our systems. It is presented in good faith. We assume no  liability expressed  or  implied as  to  design, engineering and workmanship of any project.

This is the end of the tech info for this stucco eifs and plaster product page.

Are you looking for EIFS Stucco or plaster products? Well you don’t have to look anymore. We have all the right products you need for any job big or small. We have base coats that are nice and creamy and wont dry up on you before you can put it on the wall. We have fiberglass mesh that is not to stiff to work with but yet makes great reinforcement. We have finish coats that sticks to the wall perfectly but at the same time is not glued to your float while your trying to get the job done. So you will be happy with all of our products! Be sure to check out our EIFS Stucco and plaster System pages to see how all our products come together to form a great system. Here are the products we are very proud to offer.