Elastomeric EIFS Finish Coat

 Elastomeric EIFS Finish Coat

Elastomeric EIFS Finish Coat is water resistant. It provides a textured appearance that looks great in any light. Elastomeric EIFS Finish Coat has great elastomeric qualities. It hides cracking much better then the other finishes. It can be applied over rigid substrates. We can match it to any color that you like.

 New to stucco? you can find some basic (how to) videos here.

Packaging

5 gallon pails. 70 lbs.

Coverage

Coverage per pail of Elastomeric EIFS Finish Coat for each texture is.

Medium Sand float  is. = 130 – 140 sq / ft

Coarse Sand float is. = 100 – 110 sq  / ft

Medium Quartz tex is. = 130 – 140 sq  / ft

Coarse Quartz tex is. = 90 – 110 sq  / ft

Free stylus. = Varies

Note:  Coverage will very on your job conditions. they will also vary on how you apply the Elastomeric EIFS Finish Coat.

Storage

Store the Elastomeric EIFS Finish Coat in its original pails. Store at temps from 40 º F to 110 º F. Store out of direct sun. Do not stack more than 3 pails high.

Shelf Life

It will last close to 2 years if you properly store it.

Surface Preparation

Must be clean and dry. Must be free of contaminants. Our Primer is needed for stucco and masonry application. Our Primer also may be applied as a color base.

Painted wall. Paint must have great adhesion. No more than 10 % should be remaining. Prime surface with our Primer.

Mixing

Mix the Elastomeric EIFS Finish Coat at 400 – 500 rpm. Don’t trap air. Clean water may be added.  Do not exceed 1 cup per pail. Add the same amount of water to each pail.

Note: No other additives or materials of any kind shall be added.

Curing

Initial drying will occur within 24 hours. Final cure within 3 to 4 weeks.

Application Directions

Wall shall be clean and dry. check that the wall is flat and free of defects greater than 1 / 4 ” in 10 feet. Apply the Elastomeric EIFS Finish Coat directly to the wall. Apply the Elastomeric EIFS Finish Coat slightly thicker than the largest aggregate size. Work the material to a uniform thickness of 1 / 16 “. Texture the Elastomeric EIFS Finish Coat as desired. Wipe trowel often. Apply pressure with motion to obtain the desired texture.

Note. Always maintain a wet edge. Work to corners and joints. Use Elastomeric EIFS Finish Coat with the same batch number within a wall section. Keep pail closed when not in use.

Precautions. Limitations.

Temps must be at least 40 º F during application and initial drying period. Do not use on wet surfaces. Do not use in extremely cold temps. Keep product safe from the elements. Avoid application over irregular surfaces.

Cleanup

Clean tools after use with warm water.

Warning

KEEP CONTAINER CLOSED WHEN NOT IN USE. KEEP OUT OF REACH OF CHILDREN. NOT FOR INTERNAL CONSUMPTION.

Info contained here is to the standard specs and details of our systems. It is presented in good faith. We assume no  liability expressed or implied as to design, engineering and workmanship of any project.

This is the end of the tech info for this stucco eifs and plaster product page.

Are you looking for EIFS Stucco or plaster products? Well you don’t have to look anymore. We have all the right products you need for any job big or small. We have base coats that are nice and creamy and wont dry up on you before you can put it on the wall. We have fiberglass mesh that is not to stiff to work with but yet makes great reinforcement. We have finish coats that sticks to the wall perfectly but at the same time is not glued to your float while your trying to get the job done. So you will be happy with all of our products! Be sure to check out our EIFS Stucco and plaster System pages to see how all our products come together to form a great system. Here are the products we are very proud to offer.